BMW ICOM A2+B+C WIFI Setting Guide

Here is a tutorial on how to set WIFI for BMW ICOM A2+B+C diagnostic & programming tool, hope it helps.

STEP1:make sure you ICOM A2 have a WIFI card
go to 169.254.92.38/60080
user:root
pass: NZY11502

make a self-test, than you can got the test result , the WIFI function must be OK

15-1

STEP2:Go to 169.254.92.38/58000 make the WIFI setting, ( the bmwicomshop.com bmw ICOM a2 WIFI version no need setting)
a . Set the mode to ISPI-NEXT

15-2

b . SET WLAN , SSID name ISPI-NEXT PASS:12345678 save

15-3

After the setting on ICOM is done , let’s make computer setting, suggest buy the a USB WIFI card , then set it to AP mode
Then set same SSID name as ICOM Next; ISPI-NEXT

And choose WSP2 method , enter same password :12345678

15-4
15-5

Then OK, unplug ICOM LAN cable, restart ICOM waiting it connect to laptop WIFI!

15-6

Then start ISTA/D make diagnostic. Enjoy!

HOW TO USE BMW RHEINGOLD ISTA WITH BMW ICOM

HOW TO USE BMW RHEINGOLD ISTA WITH BMW ICOM

1. Open used for connection network adapter properties, then “Internet Protocol Version 4 (TCP/IPv4)” properties, then enter 169.254.1.1 for “IP address” and 255.255.0.0 for “Subnetmask”.

2. If VMware is installed, open Virtual Network Editor and disconnect from the host any adapters with Subnet Address 169.254.0.0.

3. Open C:\EDIABAS\BIN\EDIABAS.INI with Notepad and check for “Port = 6801” in TCP settings.

10-1

10-2 10-3 10-4

4. Connect car with ICOM to PC.

10-5

5. Now run BMW Rheingold ISTA using shortcut in start menu and wait until it boots, then press settings button.

6. Select “VCI Config” tab and “HO-ICOM/ENET local and ISIS network”, then “OK”.

10-6
7. Go “Operations”, then “Read Out Vehicle Data” and “Complete Identification”.

10-7

8. Select your BMW Diagnsotic Tool from the list and press “Set up connection”button.

10-8
10-9
10-10

New Available Bluetooth Cat3 CAT Caterpillar ET Diagnostic Adapter III 2015A Heavy Duty Truck Scanner

Latest Caterpillar CAT ET 2017A Electronic Technician  P/N 317-7485 CAT3 Professional Heavy Duty Truck Diagnostic Tool New Available!!

3-1

CAT Caterpillar ET Diagnostic Adapter III is the latest generation of the Communication Adapter group, and replaces the Heavy Duty Diagnostic  Comm Adapter II. This is the only recommended communication device for et 3,and the only datalink device that will allow you to properly communicate with a CA engine on dual datalinks. This function is needed for some ET (Electronic Technician) functions.

CAT Communications Adapter III Feature:
1. WiCaterpillar Communication Adapter3
2.Allows communication between service tools and engine controls using various data links such as J1939/11, DeviceNet
(future release), CT DataLink, and J1708 (ATA) vehicle networks;
3.Flash program allows adapter firmware upgrades as additional features become available;
4.Uses J1939/11, high-speed data link (part of ADEM III controls), substantially reducing flash times;
5.Automatically selects J1939/11 when flashing the engine (reduces the flash time approximately 80%, from 14 minutes to 3 minutes).

CAT ET Diagnostic Tool CAT ET 3 III Bluetooth function:
-Display “Logged Event Codes” to show engine over speeds,High temperatures, fuel consumption, etc.
-View ECM\’s current configuration and change user settings
-Perform diagnostic tests and calibrations, and calibrate
-Electro-mechanical and electro-hydraulic components
-Context sensitive help leads operator through every task ET can perform
-Data Logger and Data Log Viewer allows recording of ECM signals for delayed troubleshooting capability.

CAT ET 3 Wireless Adapter III truck diagnostic tool Function:
1.ECM Summary screen lists every control module on equipment
2.Being tested and gives information on these modules.
3.Fast hookup and real time display of systems status. Displays ,readings such as rpm, boost, pressures, temperatures, etc. for Easy troubleshooting.
4.Identifies faulty sensors, harness connectors, and system parameters which are out of specification. Allows customers
5.To help dealer identify problems without visiting machine.
6.Identifies intermittent sensors and wiring problems during Machine operation and keeps a record of each one. Showswhen problem occurred and how often it happened.
7.Added information to allow customer to assist dealer in diagnosing and repairing problems. (Troubeshooting Help is not built in with in the program, you will still need go back to books in order to follow a repair description and steps in each Fault Code display within the program).English and metric units of measure integrated help file to easy learn the “How To” around the software.

CnAutotool.com provide best quality CAT Communications Adapter III with laptop. You can get it to work when you receive the package. Our engineer will activation the software for you, it is very convenience and easy to use.

How to Setting WIFI Connection for Volvo 88890300 Vocom Interface ?

How to Setting WIFI Connection for Volvo 88890300 Vocom Interface ?

Volvo 88890300 Vocom Interface is a diagnostics application that covers the whole repair process through the use of plug-ins. With Volvo 88890300 Vocom Interface you can diagnose, test, calibrate, and program a product. Volvo vocom support wifi for Volvo/Renault/UD/Mack , so how to setting the wifi connection when you use it ?

Lets check the steps :

1.Please use the USB cable adapter connect with your laptop and Vocom main unit .

2.Go to open Volvo PTT software. Choose “Setting” → “Communication unit configuration”→ “Configure”→ “USB+ Directly to Communication unit”.

3.Choose “Direct” → “Restore default values” → “Apply” → “OK”.

4.Click OK again then disconnect the USB cable from laptop.

5.Go to “Setting” → “Comm.unit Selection” → “Communication unit 8889300 ….Nickname”

6.Now you can use signal and get wireless signal. All OK. In this way you can set Volvo Vocom 88890300 Interface WIFI connection easily and successfully

Thank you

CNAUTOTOOL Team

 

Solution about MB STAR C4, MB STAR C5 Update and can not test vehicles problems

Make sure your computer hardware version is higher the Car Diagnostic Scanners Tools mb star c4 or mb star c5 version, otherwise, CSD will show update failed . Bootimage can update successfully. The following picture show how to check the mb star c4 or mb star c5 version1
3-1
The following picture is show your computer hardware HDD software version66
3-2
If their software is not same, it no need update ( because factory has upgraded the latest version of the mb star c4 or mb star c5 machine)

If customer not use our HDD software, it will appear read vehicle failed problems.

Solution as following

(1) Mb star c4 or mb star c5 supply power to confirm the machine was turn on, like the following picture ( If now show the three icon, it means the mb star c4 or c5 main unit is broken)

3-3

(2). connect LAN with computer, confirm computer IP change to172.29.127.118, like the following picture :

3-4

(3)  change of software using pattern (Because you modify the software for the firmware upgrade mode, the software is not test the vehicles)The following picture is show the software is upgrade mode

3-5

The following picture is show test read vehicle mode.
3-6

Three files name Update_automaticx , Update_manualx ; Update_SpecialxThis is read vehicle mode, if can not read vehicle, please change files name, then restart computer

Launch Creader Professional CRP129 Premium and CRP123 Premium Comparisons

Good news that we have the LAUNCH CRP 123 Premium and CRP 129 Premium in stock now , and they are the new solution for car owners and services for express-diagnostics, with the maximum possibilities at relatively low cost.

For models LAUNCH CRP 123 / 129 Premium device capabilities allows read and erase error codes with explanations, read the current data on the four basic systems of the car – engine, transmission, ABS (ESP, DSC), Airbag (SRS), and for CRP 129 Premium are offered additional features for programming and service intervals resetting, some basic adaptations for the main important functions and ability of diagnostic of the system EPB (electronic parking brake) / SBC ( Sensotronic brake control module).

 

Solution CRP 129 Premium on CnAutotool.com is especially useful for small services, service reception points and body/repair services for express-diagnostics depending on the requirements to the level of diagnostics, and low-cost CRP 123 Premium is suitable even for private use of individuals who have some of their own cars. Little size equipment allows to take it easily with you or express mechanic and make right on the road preliminary diagnosis. Easy and intuitive menu allows using it to anyone, even a service mechanic or private person

 

More details for the comparisons , please check as bellow :

 

Model

CRP 123 Premium new!

CRP 129 Premium new!

Supply voltage, V

9-18 V

9-18 V

Connection type, ability to use the

adapters for old diagnostic sockets

OBD-II,

not supported

OBD-II,

not supported

Complete scanner OBD-II mode

+ , all functions

+ , all functions

Read and delete factory fault

codes (for factory protocols)

+, more than 40

world brands

+, more than 40

world brands

Display the current

data in digital form

+, up to 4 parameters

simultaneously

+, up to 4 parameters

simultaneously

Display the current data

in graphical form

+, up to 4 parameters

on one chart

+, up to 4 parameters

on one chart

Recording of the current

data and screenshots  in

the device memory and replaying

+, up to 32 records

+,  up to 32 records

Replaying of the saved data,

Freeze Frame and historical

error codes

+

+

Read of VIN

(control units that support this feature)

+

+

Reading and display of the

identification information

of the control unit

+

+

Search the fault codes by

entering them with the buttons

+

+

Built-in help, DTC hints and

location of the diagnostic socket (DLC)

+

+

GOLO functions

Help, community and

online diagnostics

-

-

Reset and setting service intervals

inspection 1, 2

and inspection mileage

-

+

Steering  angle sensor adaptation

and reset, brake pad

locking/unlocking and checking

-

+

Number of supported systems

on factory diagnostic protocols level

4 main systems

(ENG,ABS,AT, SRS)

4 (ENG,ABS,AT, SRS)

+ 1 (EPB/SBC)

Multilanguage interface

+

+

Recording in the memory and printing

of the diagnostic reports via PC

+

+

Quick free update

via Internet

+

using the

USB 2.0

+

using the

USB 2.0

Screen

color, 4”, 480*320,

LCD TFT

color, 4”, 480*320,

LCD TFT

Support of Wi-Fi,

USB

no,

USB 2.0

no,

USB 2.0

Built-in clock and

switchable buzzer

+

+

Operating system

Windows CE 5.0

embedded

Windows CE 5.0

embedded

Main technical parameters

CPU 120 Mhz single core,

RAM 1 Mb, 4 Gb SD Card

(up to 32 Gb)

CPU 120 Mhz single core,

RAM 1 Mb, 4 Gb SD Card

(up to 32 Gb)

Support of application

installations

-

-

Web browser,

e-mail client

-

-

Multimedia functions

(video, photo, etc.)

-

-

Additional prospect

download in English

Short update manual

  download in English (protected)

 

There also have a video of Launch X431 scan tool CRP123 Premofor your reference as bellow , please check

Video