Failed to code a Nissan key after changed ECU

Problem:

Nissan 2000 model diesel after changing ecu and key, I am failing to code a key. I have several Car Key Programmers in hand, including T300, SKP-900, SBB etc, but they  just saying communication failed. Any idea how to fix the problem?

31-1

31-2

31-3

Possible solutions by cnautotool technician:

Check dash if engine light come on if not check power go ecu if power got live to ecu come on that mean ecu fail then get new ecu swap chip or reprogram ecu. If the check engine light is on, you need a dealership computer to reprogram a new ecu (swap chip from old ecu to new ecu use old key back).

The old ecu have been stolen but I can program the key with immo by Tango key pro, the problem is just ecu how to swap it.

There’s also a eeprom on the ecu that can be done by a tango.

Need old ecu to get eeprom most important but I will say try this computer Nissan consult iii to to full reprogram ecu and on car.

Ok right now I have two ecu one is new i both it in Africa another I bought from CnAutotool.com old it’s possible to get the eeprom on the old ecu.

Yes soldered out chip and put new ecu.

2.Use MVP (the Key Pro M8)/T300 with Nissan -16 adapter it will work.

Will AK90 read mileage from BMW Key E91 2007

Question before entering:

I’m  looking for a tool to read mileage from BMW KEY from BMW E91 year 2007. I want only read it not change it.
Someone knows which tool i can do that? I heard that Obd2 Key Programmer Tango will do, but i am not willing to spend that money if only need to read it. AK90 key programmer possible?

BMW expert solution:

AK91 plus will identify keys for all EWS and CAS , showing VIN , key No. and mileage from 1995-2009.

BMW AK90 key programmer can read km from key.  I read some for E46 2005 before. I test E91 2007 today. It reads no problem.

26-1

26-3

But if you need to change/correct mileage on E9x, you can go for Tango Transponder Programmer or Digimaster 3 odometer correction master.

Ford Transit 2007 All Keys Lost What Tool to Program?

Problem:

Hi, I need to make transponder for a new key, since old keys are lost.
It is Ford Transit model 2007, ecu Fo mo co 6c11 12a650 ak. Where are data for key stored in ecu, dash or in body control module?
I disassembled the ecu but I am not sure where the immo data for keys are stored. there is st 10f275 mcu, but I cannot find the eeprom. Are these data stored in the ecu at all? Or they are somewhere else in dash or general module?

Locksmith solution:

Ford Transit 2007 key data is stored in the BCM immo box behind the glove box MC9S12DT256 4L91N.
Read that dump 9s12 and add key with Tango Key Programmer etc but very long winded.

Easier to relearn new key with Ford VCM2 IDS.

You will need 2 keys if using Ford IDS.

4D63 80 bits transponder from CnAutotool you don’t neet the dump read just make key turn ignition add key via IDS.

Will Tango Program Key for Passat CC 2013 US Model

15-1

Q:

Hi, Is it possible to make spare key with Tango Transponder Programmer by dump?
Car is 2013 USA.

A:

US Passat, some have the immo in the cluster.
Tango covers ccm comfort  modules.
You could read the ccm, and check for Keys!

CCM is located behind the glovebox.
Look for something like this:
Hitag keyless module 3C0 959 799 H
Regular id48 key module 3Co 959 433 AQ

How to clone DST via Tango Key Programmer

Here is the tutorial on cloning DST Transponder by using original Tango Key Programmer.

Note: The document is only for education purpose. You can check the instruction on original website scorpio-lk as well.

Currently only Toyota and Yamaha keys are supported.For more details, Toyota supported keys have the 1-st page from the following set:
X0
X2
X3
X4*

X4*-only european market supported.

Cloning DST Transponder by Tango:
Run the Clone Mode selecting the appropriate menu item:

10-1

The next screen will appear:

10-2

Place an original key on the Tango and click “Read original key” button

10-3
Once the TIRIS DST or DST+ transponder detected the “Decode Transponder” button appears:

10-4
Click the “Decode Transponder” button. Obd2 Key Programmer Tango software will prompt to to decode transponder:

10-5

Tango transponder programmer will run the decoding process:

10-6

In case the decoding finishes successfully the “Write Clone” button will appears:
10-7

Now,remove the original key and replace it with EH2 (battery emulator) or TPX2 transponder. You are all set to make a clone. Click “Write Clone” button and Tango will do it.

CnAutotool Provide Automotive diagnostic tool, diagnostic software,More information Contact us sale@cnautotool.com Senior Sales Engineer

Introduction for Original Tango Key Programmer

Tango programmer is a new generation of transponder programmer which is developed to cover, read, write and generate the latest transponders used in the latest vehicle immobilizer technologies. New function for reading the Kilometers, VIN and transponder type for all BMW keys was added to the BMW software module! Immo pin code is also displayede for some car models. With this programmer you can generate images for many different original transponders like Philips ID33, Philips Crypto for different ID’s and Texas crypto!

The device at CnAutotool  is intended for programming of transponders , that are a part of automobile immobilizing systems.
Unlike the previous model the Gambit, new model Tango is the two-band device that has allowed to add the list supported transponders with firm Texas Instruments products.

The Tango Programmer is the next generation of transponder programmer which is continuously developed to cover, read, and write the latest transponders used in the newest vehicle immobilizer technologies.

New function for reading the Kilometers, VIN and transponder type for all BMW keys has been added to the BMW software module.

Please note after generating a new transponder with TANGO Programmer, you do not need any additional diagnostic equipment to program the generated transponder to the car. It will start the car directly, even on new FIAT CODE 2 system, which is also used in PSA Group vehicles. You only have to write the new file back into the immobilizer system.

TANGO KEY PROGRAMMER WITH BASIC SOFTWARE

Tango programmer is a new generation of transponder programmer which is developed to cover, read, write and generate the latest transponders used in the latest vehicle immobilizer technologies. New function for reading the Kilometers, VIN and transponder type for all BMW keys was added to the BMW software module! Immo pin code is also displayede for some car models. With this programmer you can generate images for many different original transponders like Philips ID33, Philips Crypto for different ID??s and Texas crypto!

!!!!!! VERY IMPORTANT !!!!!!

After generating a new transponder with TANGO Auto key Programmer, you will not need any additional diagnostic equipment to program the generated transponder to the car! It will start the car directly, even on new FIAT CODE 2 system, also used in PSA Group vehicles! Only you have to write the new file back into the immobilizer system!