How to enable DoIP communication for SD Connect C4 clone

Test report: MB Star diagnosis SD connect c4 version 2019 cloned multiplexer now can support ethernet communication (DoIP).

Here you go….

Go to Xentry Diagnosis

sdconnect-c4-doip-test-report-1

sdconnect-c4-doip-test-report-2

Diagnosis steps:

Step 1: the boundary conditions are recorded

Step 2: the control units are being initialized

Step 3: check vin

Step 4: the coding of the control unit is read

Step 5: the emissions-relevant data are read out from the vehicle

sdconnect-c4-doip-test-report-3

Xentry diagnosis overview

sdconnect-c4-doip-test-report-4

The data are being determined

sdconnect-c4-doip-test-report-5

Select A26/17 Audio 20 (Head Unit)

sdconnect-c4-doip-test-report-6

sdconnect-c4-doip-test-report-7

sdconnect-c4-doip-test-report-8
Important notes:

– it is recommended to connect a charger. the battery voltage must be higher than 12.50v

– the data read out of the control units refer to specific events or system statuses and serve as a basis for narrowing down the source of the defect. the data maybe include a tolerance and it may therefore not necessarily be possible to link them to a certain event, location or time.

sdconnect-c4-doip-test-report-9

ESD

hazard due to electrostatic discharge

Safety instructions/precautions

– to avoid damage to control units, antennas, sensors etc. due to electrostatic discharge (ESD), the technician must comply with the appropriate safety precautions before replacing electronic components

– proper static discharge can be guaranteed very effectively by means of a grounding strap for the wrist connected ground

– alternatively, static electricity can be discharged by deliberately touching

– repair or cleaning work on electronic components may only be performed on an ESD worksurface using a grounding strap for the wrist to ground the body
sdconnect-c4-doip-test-report-10

establishing communication with control unit A26/17 Audio 20 (Head Unit)

sdconnect-c4-doip-test-report-11

sdconnect-c4-doip-test-report-12

reading coding data

sdconnect-c4-doip-test-report-13

actuation of function “ethernet communication (DoIP)”

sdconnect-c4-doip-test-report-14

sdconnect-c4-doip-test-report-15

sdconnect-c4-doip-test-report-16

sdconnect-c4-doip-test-report-17

sdconnect-c4-doip-test-report-18

sdconnect-c4-doip-test-report-19

MB SD connect C4 2019 ethernet communication (DoIP): checked!

Ford Escape 2013 Replace/Program/Calibrate PCM with Maxisys Elite + J2534

Today I am going to share with you a case study on how the Autel owner experience with his first j2534 programming event.

Purpose: Needed the solenoid body id/ strategy code in order to complete a pcm programming

Car: Ford Escape 2013

Device: Autel MaxiSYS Elite and J2534

Background: client secured a new auto body repair contract and was going to attempt his first programming procedure on new pcm module. while assisting him we discovered Ford software was requesting the solenoid body id/ strategy code but could not retrieve this information since it was a new pcm module installed on the vehicle

How to: locate the solenoid body id/strategy code to complete pcm programming procedure

PCM removal

Maxisys-Elite-ford-pcm-programming-1

New PCM module

Maxisys-Elite-ford-pcm-programming-2 Maxisys-Elite-ford-pcm-programming-3
Solenoid body tags location

solenoid body tags:

Maxisys-Elite-ford-pcm-programming-4 Maxisys-Elite-ford-pcm-programming-5 Maxisys-Elite-ford-pcm-programming-6 Maxisys-Elite-ford-pcm-programming-7

Problem:

Cannot locate the body id tag

May need outsource to dealer

Loss of reputation/business relationship

Solution:

Get an original PCM

Old PCM module installed

Maxisys-Elite-ford-pcm-programming-8 Maxisys-Elite-ford-pcm-programming-9 Maxisys-Elite-ford-pcm-programming-10

Maxisys-Elite-ford-pcm-programming-11 Maxisys-Elite-ford-pcm-programming-12 Maxisys-Elite-ford-pcm-programming-13

programmable parameters
transmission
transmission characterization
document id codes

Program the PCM module:

New PCM module installed

Maxisys-Elite-ford-pcm-programming-14
Reset passive anti-theft system (PATS) parameter:

vehicle without keyless entry and push button start for the 2013 escape

turn the ignition key cylinder from OFF to ON
in Maxisys Elite, select Hot function – immo – PATS functions and follow up the screen instructions to enter the PATS security access
from the Elite, select “Parameter Reset” and follow the on-screen instructions
perform the misfire monitor neutral profile correction procedure

Maxisys-Elite-ford-pcm-programming-15 Maxisys-Elite-ford-pcm-programming-16 Maxisys-Elite-ford-pcm-programming-18 Maxisys-Elite-ford-pcm-programming-19 Maxisys-Elite-ford-pcm-programming-20

GDS VCI For KIA & HYUNDAI software has not been updated for over 4 weeks now, How to Solve?

Hi. I installed the GDS software about 2 month ago and today when I went to use it, it tells me that this software has not been updated for over 4 weeks now. Connect to internet or you will have limited capability.  I did not connect to the internet. The computer that is installed on, can’t go on the internet. How can this be fixed.

How - to - Solve

A: change computer time to 2016.9 to try it. so it is working.

Top GDS VCI for KIA & HYUNDAI with Trigger Module

Buy it for 8 reasons:

1. With Trigger Module, Flight Record Function
2. Firmware V2.20 Software Hyundai V19, kia v12
3. Update by CD
4. GDS VCI Vehicles Coverage : 1996-2017 some new car models for Hyundai Kia
For Kia, it can be supported till 2013.
For Hyundai, it can be supported till 2017.
5. Package come with USB Dongle, software installation more convenient
6.Wanted to checked the supported car list for hyunday? click this video
7. How to install GDS VCI Hyundai V19 video
8.How to install GDS VCI Kia V12 video

Notice:

1. Language: English Only
2. Operating System: Windows XP/Windows 7
3. Kia and Hyundai software cannot install in same computer.The installation step is a little long.
4. GDS software mainly support North America vehicles models, please use OBD software for Hyundai Kia.

GDS VCI Diagnostic Tool for KIA Hyundai Features:

1) Completely Integrated Diagnostic System with User Specific information & settings
2) Complete Technical Service Information
3) Comprehensive & Customized Diagnostic Solution
4) Guided Troubleshooting Procedures
5) Mobile Data-recording Function
6) Real-time Software Management

Trigger Module (Flight Record)

Intensified recording function of vehicle conditions at idling or driving
Recorded data VCI can be reviewed and analyzed precisely and the terminal
Exact Analysis of data trend
Data storing in PC and sharing for remote control diagnosis and further diagnosis
Actuator Driving
Sample Operation and multi-record with large memory up to PC HD memory
Easy to use and fast procedure

GDS Software Installation Tips:

1. Kia and Hyundai software can not be installed on the same computer. Before install Kia software, it must install hyundai master dvd,  otherwise it will cause the softwre install not success

2. Never try to update the software, otherwise the circuit board will be burned, need return it back for repair,and you will pay all the maintenance cost and shipping cost back and force, because such damage is not free in the warranty policy.

GDS VCI Diagnostic Tool is an advanced service system that provides comprehensive coverage for all Hyundai vehicles including all Hybrid cars. Professional Diagnostic Tool GDS provides complete diagnostics, analysis and reprogramming capabilities as well as a huge library of technical, service and repair information. And now buy it. you can get NEW kia GDS software free.

GDS VCI Packing Including:

1pc x VCI Interface (Optional Color:Red/Blue)
1pc x OBD2 main cable
1pc x 20 Pin Adapter
1pc x 12 Pin DLC Cable
1pc x 10-8-2 Pin Cable
1pc x 6P DC Jack
1pc x AC-DC Power adapter
1pc x USB Cable
1pc x U Disk( Kia,  Hyundai )
1pc x Trigger Module (Fright Record)

OBDSTAR X300 DP PLUS/ X300 DP New update 2019/7/8

OBDSTAR X300DP PLUSX300 DP New update 2019/7/8:
Renault 2016- Clio IV / 2015- CAPTURE / 2018- symbol key programming
Maserati Ghibili pincode reading+smart key programming

Dodge Charger/ Cherokee 2019 odometer reset
Maserati Ghibili 95320 odometer reset

OBDSTAR - X300 - DP - PLUS -1

OBDSTAR - X300 - DP - PLUS -2

OBDSTAR - X300 - DP - PLUS -3

How does CGDI BMW diagnose BMW 3 series E93 successfully?

How to update CGDI BMW diagnosis function for free:

As long as you have any of CG100 or CGPRO or CGDI MB, please provide the serial number for free trial.

For BMW diagnosis: CGDI BMW VS BMW ICOM

1.Easy to use. As long as you are qualified with corresponding vehicle maintenance knowledge, CGDI BMW does not have high requirements for the user’s professional skills and English level.

2.Cheap. Car Key Programmer CGDI BMW is cheaper than BMW ICOM (clone and original).

BMW ICOM clone & original are able to diagnose, program and code BMW E-series models at higher price (clone: about 400eur).

Besides, BMW ICOM has some requirements for the user’s operating skills during installation, therefore some users will choose a hard disk with pre-installed software and be charged.

3.Menu-driven & automatic operation instead of manual operation, which save much time.

How does CGDI BMW diagnose BMW 3 series E93 successfully?

1.Select “BMW diagnosis”.
series E93 -1

2.It pops up “Whether to scan vehicle quickly”.

Press “Yes” and CGDI BMW will scan the BMW in 30 seconds.

Press “No” and CGDI BMW will scan the BMW all systems and take about 3 minutes.

series E93 -2

3.After selecting “No”.
series E93 -3

4.It pops up the BMW information.

Have diagnosis options :

Read fault codes, clear fault codes, Clear all codes, Help, back.

It is menu-driven operation, easy to use.

At the left corner, you will see the working status.

series E93 -4
series E93 -5 series E93 -6 series E93 -7

5.Back to select “BMW diagnosis”, then “scan vehicle quickly”.

And you will see all trouble codes are cleared, and all are normal.
series E93 -8 series E93 -9 series E93 -10
Don’t you think it is easy to use CGDI BMW Prog for diagnosis?

Xentry Openshell XDOS 07.2019 Acronis Image + Pactch + Keygen

07.2019-xentry-xdos-download-01

System requirements: HDD or SDD 250 Gb, 8GB RAM, Windows 10 64bit

Interface language: multilanguage

Description: Image of programs for diagnostics, coding and programming of cars

XENTRY 07.2019 CHECK LIST:

Developer Kit ?

DAS Password Free Special Functions?

Adding W204-W212-W166 in DAS?

Special Function Password Free SMART?

Xentry Special Functions Calculator?

SMART SAM 450&452 inside ECU adaption

SMART ESP Extra Coding+Dev. Data ?

Superess ALL TAN codes Smart Equipment

Passwordfree Offline Key Teach in Smart

Offline SAM Assignent?

TRANSPORTER Special Function Passwordfree Coding/Flashing Offline?

SD FLASH Offline in DAS all Vehicules ?

LKW Nox Torque Limit Setting FDOK XT Automatic in DAS no password calc need ?

LKW NFZ Erase SCR AD BLUE fault code?

NFZ Sonderfunktion Passwordfree?

Added Offline EOL & VMAX all LKW ?

HHTWIN HHTPKW&NFZHHT ready?

Vediamo Level 10 whit 9GB shortest ?

Vediamo 100GB Data Base ?

New Keys for Xentry?

BUS Licences MB & Setra ?

Ready for Online/Offline ?

Sd Connect C4-BENZ C5-Benz C6 & VCI Ready by Wifi

All Server Online !! ?

Addon Updates Works 100% ?

SUPPORT 24/7

07.2019 MB STAR Acronis Images:
07.2019-xentry-xdos-download-2 07.2019-xentry-xdos-download-3 07.2019-xentry-xdos-download-4 07.2019-xentry-xdos-download-5 07.2019-xentry-xdos-download-7

Solution to Nissan consult III error “No registered VI/MI?

Nissan consult iii installation error ” There are no registered VI/MI. Please contact your administrator”. The device is Nissan Consult 3 Renault can clip 2-in-1 diagnostic tool.
nissan-consult-3-installation-guide-1 nissan-consult-3-installation-guide-2

Possible reason and solution:

1). Nissan Consult 3 Plus software and Renault can clip software were installed in the same computer. Which caused the conflict.

2). Besides, Nissan Consult 3 should be installed by following the correct instruction, the device must be added to the software.

Nissan Consult 3 software installation procedure:

PASSWORD:nissanconsult3 (for registration)

nissan-consult-3-installation-guide-3 nissan-consult-3-installation-guide-4 nissan-consult-3-installation-guide-5 nissan-consult-3-installation-guide-6 nissan-consult-3-installation-guide-7 nissan-consult-3-installation-guide-8 nissan-consult-3-installation-guide-9 nissan-consult-3-installation-guide-10  nissan-consult-3-installation-guide-12

JMD Handy Baby II OBD Diagnosis, Odometer, IMMO and MQB Vehicle List

JMD OBD adapter for JMD Handy Baby II key copy machine soon release VAG MQB odometer correction.

jmd-obd-function-1

Note:

MQB function requires JMD OBD adapter. The adapter only works with Handy baby II.

Handy baby ii cannot do MQB all keys lost.

Handy baby 2 OBD does not support JCI dashboard offline programming, always do it online. Online need extra token.  Offline programming does not require token.

After you get the OBD,send us your OBD ID to open the MQB function.

JMD OBD Adapter Function:

All JMD Assistant function
OBD Programming
Automobile diagnosis
Odometer correction
Remote control manual programming
VW/Skoda/Audi MQB

MQB token list
1. Magotan MQB
2. Golf 7 MQB
3. Lamando MQB
4. Skoda Octavia MQB
5. Tango MQB
6. VW Touran MQB
7. Passat pre-2019 MQB all keys lost
8. Audi A3 MQB
9. Audi TT MQB

jmd-obd-function-2
JMD OBD vs. old JMD Assistant

jmd-obd-function-3
JMD OBD Diagnostic Car List

VW
Audi
Honda
Toyota
Nissan
Citroen
Suzuki
Buick
Chevrolet
Ford
Mazda
Dongfeng Aeolus
Haima
JMC
Brilliance auto
Chery
Southeast
Mitsubishi
Great Wall
Geely
Englon
JAC
Changhe
BYD
MG
LIFAN
ZOTYE
SGMW
LOTUS
HAFEI
ZXAUTO
CHANGFENG
Land Rover
Renault
Dodge
Subaru
Jeep
BMW
Benz
Ssangyong

Opel
Jaguar
Lincoln

JMD OBD Remote Programming Car List

VW
Audi
Buick
Chevrolet
Cadillac
Kia
Hyundai
Roewe
Ssangyong
Renault
Porsche
Ford
Nissan
Infiniti
Smart
Land rover
Skoda
Mazda
Great Wall
FAW BESTURN
Geely
GMC
Jeep
Chrysler
Jaguar
Dodge

JMD OBD IMMO programming car list

VW
Audi
Hyundai
Buick
Chevrolet
Honda
JINBEI
Brilliance Auto
Citroen
Peugeot
Dongfeng Nissan
Kia
DFL-FX
Toyota
TJFAW
Southeast
Chery
ZZNissan
Mazda
Leopaard
Ford
Changan
Changhe
Ceely
HAFEI
JAC
JIANGLING
Great Wall
HAWTAI
MAPLE
LIFAN
ZOTYE
FAW BESTURN
YOUNG LOTUS
SAIC ROEWE
HAIMA
SAIC MG
Chrysler
Renault
Subaru
Jaguar
Cadillac
Land rover
Lexus
Mitsubishi
Infiniti
Ssangyong
Jeep
Dodge
BYD
Smart
Luxgen
Baojun
Beijing Auto
Fiat
Trumpchi
Yema
FAW JIABAO
GMC
Hummer
Iveco
Maserati
Suzuki
Isuzu
DS

CGDI MB Program Mercedes EIS A246 All Keys Lost

New test report:  Programming CLA 2014 with EIS A246 ALL KEY LOST with CGDI MB success in 6 minutes including password calculation.

Model: Mercedes CLA 2014 S A264

Devices to program: CGDI Prog MB Benz and AC adapter for quick data acquisition

Step-by-step procedure:

Step 1: Calculate password

Connect AC adapter with CGDI MB and EIS

cgdi-mb-a246-all-key-lost-1

Read EIS data

cgdi-mb-a246-all-key-lost-2

Then go to Compute Password- Copy key without key- Collect data-OBD mode

cgdi-mb-a246-all-key-lost-3

Insert the simulation key into EIS in 30s

CGDI MB AC Adapter collects data very fast

cgdi-mb-a246-all-key-lost-4

Save key file

cgdi-mb-a246-all-key-lost-5

Upload the data to calculate password

cgdi-mb-a246-all-key-lost-6

Upload data successfully, press Query Results

cgdi-mb-a246-all-key-lost-8

Calculate password success. Copy the pass

Step 2: Generate Key File

Go to EIS, read EIS data

cgdi-mb-a246-all-key-lost-9

Paste password here

cgdi-mb-a246-all-key-lost-10

Save new EIS data

cgdi-mb-a246-all-key-lost-11

Go to Generate Key File

cgdi-mb-a246-all-key-lost-12

Load EIS data just saved

cgdi-mb-a246-all-key-lost-13

Choose key file format V51 and Generate key file

cgdi-mb-a246-all-key-lost-14

Key successfully calculated. Save them

Step 3: Write Key

Now go to write new key with CGDI MB

Select Read/Write Key function- Read Key/Chip

cgdi-mb-a246-all-key-lost-15

Insert new key into CGDI Prog

It is a blank key. Press Open/Write

cgdi-mb-a246-all-key-lost-16

Choose common BE key format V51

cgdi-mb-a246-all-key-lost-17

Choose a key position

Write key success

New key is not activated until we insert it in EIS

Done.

How-to’s of 2006 Corvette M6 BCM fix with GM Tech2?

Car model and year: 2006 Corvette M6

Symptom description:

The new column lock replacement parts have been installed in my 2005 M6 and now I need to instruct the BCM to ignore any odd codes from the column lock as a part of the fix outlined in the TSB.

Tool to use:

GM Tech2

TIS2000

Guidance:

Will need to pick up a Ac Delco subscription for $40 to start with so you can get access to the new firmware file.

Next, if you don’t have a rs-232 port on your laptop, will need to buy the needed USB cable so you can connect the tech II to your laptop on a USB port.

gm-tech2-do-bcm-fix-for-2006-corvette-m6-1

Now the easy part, Put the tech II into pass through mode, connect it to the car with car in run mode motor off, and bring up TDS on your machine to use SPS.
Now using TDS SPS, run through it until you get to the modules mode, and and select Body control module.

In the firmware selection screen utility to disable the steering control lock in calibration, and flash that it.

This will cover you to see what to select the firmware file to flash in.

FYI, it’s a new file and one that will not be in TIS2000 unless you have an active account that can connect to GM to pull the needed updated firmware file that was just released this year. Most don’t, so TDS for $40 for two years it the cheaper option.

A frustration to be solved:

Got the usb to rs232 cable and the $40 subscription but cannot for the life of me get the laptop to connect to the Tech2 and the car. I am getting messages from the website to restart my programming interface and when I log in and try to add the VIN, the website takes me to a bunch of warning messages and unread alerts. Once I get SPS up and try to run the process after selecting the Tech2 pass through mode and checking the connection, I just get error messages. I have gone the rough the connection and login process several times and followed the connection instructions on SPS exactly. I don’t know if I need to enter the VIN someplace but can’t seem to do that. The Tech2 connects to the car fine so it has to be the web, laptop, tech2 connections that is not happening..

Solution:

When you start SPS the first time, you have to set it up correctly. There are a few programs that you needed to download and install, as well as allowing a few sites to get through, then final Java updates that are needed.

After this and you have sps start up, when you get the first pop in SPS , did you install the Tech II J2534 driver or not?
gm-tech2-do-bcm-fix-for-2006-corvette-m6-2

Lastly, with Tech II connected to the machine, go in device manager and make sure that the tech II is showing up in the list as well.

Also to point out, not sure where you bought your Tech II kit from, but should have come with a candi module from the start that should be in play.

gm-tech2-do-bcm-fix-for-2006-corvette-m6-3

Myself, I just use a VX nano most of the time, since the VX driver works for SPS (don’t have to load either bosch drivers), nor play the extra candi/usb cord since the usb cord that comes with it is all that is needed for SPS programming.